1999 Audi A4 1.8T w/Concert headunit

The real reason for this article is to help people out with the wiring diagram for the harness in the 1999 Audi A4s. That is the primary piece of info that would have helped me out online. Otherwise, the info here is pretty standard and this is NOT a super hi-fi set-up experience. This is a "I want the harness wiring diagrams to fix/replace my rear amp" experience. Hopefully this article makes you feel more comfortable about attempting this.

I purchased a pre-owned A4 sigh-unseen for a great price that came delivered with a missing rear-amp (and turbo clamp and ac belt, I quickly discovered! :) ). Although the dealer offered to get me one as soon as another A4 came through his lot, I opted to just install a third party amp rather than wait (after waiting 4 weeks first) and to avoid the fact that if the dealer pulled it from another A4, then someone else would have to deal with it. That just didnt seem right to me. And since the dealer was apparently dumping this otherwise good Audi for such a good price for the reasons explained above, I couldnt complain about this very simple and inexpensive fixes. However, the rear-amp fix, if I used an Audi part (8d5035401), which came as both speaker and amp only, would cost about $200 with no dealer mark-up. Since it was such a dinky amp (the base Concert speaker set-up), I figured a 200w 2-channel amp from anywhere would actually be better. I got one for $50 from Walmart, no less, to fit the bill.

The rear amp is a smallish thing, normally attached to the rear left speaker (sedan) in the rear deck plate. It appeared to me the amp had somehow been broken off the speaker as parts of the molding on the lower portion of the speaker were broken. The harness that comes from the head unit was just dangling. I searched for wiring diagrams for the harness but no luck, so I got out my trusty multi-meter, a small pc-speaker with stripped wires, and went to work. Here is the wiring diagram:

The brackets represent the slots that slid into the male harness end. The side with the outward piece is the piece I chose as the "top".

________[ ]________
(1) (2)
(3)
(4) (5)
(6)
(7) (8)
________[ ]________

1: White- Switch
2: Red-Blue lead to Right speaker
3: Brown-Red lead Right speaker
4: Red-Blue (thicker): 12v
5: Blue-Green Right pre-amp from head unit. I am assuming they are pre-amps as I got a voltage reading of about 1v with the volume full blast. It was just enough to just barely run the speakers or the pc-speaker at full blast as well.
6: Red-Green Left pre-amp from head unit
7: Brown (thicker) Ground
8: 2 Brown-black Grounds for pre-amp leads.

You should probably check this out on your harness if you are replacing your stock amp (and/or speakers) to make sure. You know the disclaimer routine.

As you can see, there are no left speaker leads. My understanding is the amp/speaker setup comes with the amp having a direct connection to the left speaker terminals.

First I cut off the harness, stripped wires, and loose-wired all the wires to my new amp before mounting. Once I was satisfied again that everything was what it appeared, I proceeded to mount the amp with four galvanized zip screws to the rear deck from below. I made sure to attach it to double walled areas with nothing above it so they wouldnt come through the deck. I also removed the rear deck cover to facilitate in running wires, but it really didnt help that much anyway. I mounted the amp close to the left speaker as I had already mounted a 6-CD changer to the rear deck near the right speaker. I was able to put the amp quite a ways back and out of the way. Because the amp was so cheap (but still well overmatched for the crap base speakers Audi put in) and light that I am sure the 4 zips would hold it there fine forever. If you are doing this with a real amp that is heavier, I might suggest actually bolting the amp to the rear deck. Then I proceeded to really wire. Since my amp had rca jacks in, I had to cut up an RCA cable, strip wire that to the pre-amp leads. All the pre-amps and leads I finger wired together, folded over, and wrapped with electricians tape, then wrapped again with a layer of gaffers tape. The power and the switch I used orange (small) wing-nuts and then wrapped with electricians tape. I did not use the #7 Ground/Common and grounded the amp directly to the rear deck. I dont think it matters to not use the harness ground, and perhaps I should have tested that... If anyone has a good reason you should, please let me know as I would be happy to know that if it helped anything out.

For amp-to-right speaker connection, I actually pulled into the wire run that came into the harness where it passed by the amp and ran it directly the amp rather than piggy-tail it from the harness point. For the left speaker, since I had the rear deck cover off, I measured my needed speaker wire length, cut it, then took out the speaker and soldered the wire length directly to the terminals. Then I reinstalled the speaker and ran the wire to the amp. This only required about an 10 inch length of speaker wire.

I tested everything, turned the gain almost all the way down on the amp (this seemed to match the front speakers best). Left it on flat (full range) for crossover (that seemed to be best as well), and left the bass-boost (loudness) on. I put everything back together and tested again. Great! The stock sound system in the A4 pretty much sucks, and this new amp pretty much didnt change a thing to that status I am sure (I have test driven other A4s with same sound system and they sound pretty much the same, sucky). But at least the rear speakers were working again. It made me really appreciate my "Sun & Sound" package Infiniti sound system in my 2003 Mitsubishi Eclipse! Wow, what a difference. But I would say that the A4 sounded about the same as my 2000 Honda Accord EX with the JBL speakers and stock head unit (again, nothing to rave about, but fine for just plain old drive along music/news).

One thing I noted: The right speaker was marked 4ohm. My amp was 8ohm or 4ohm bridged. Since my amp was cheap, but surely had much more wattage (even if we assume the real wattage of this 200w amp is only 40-60w/channel sustained that had to be more than the miniscule little amp that is installed on the stock system), hooking up small 4ohm speakers to an 8ohm amp meant that the speakers would draw more than it should, but so what. I think it will handle it.

Short Description
The new 3.0 litre six cylinder BMW X5 4WD wagon is a welcome addition alongside the 4.4 litre V8 version as it costs $25,500 less, provides commendable levels of performance, returns better fuel economy than the V8, and still provides most (but of course, not all) of the V8 model’s desirable features.

Quite apart from whatever value you put on the BMW nameplate, that’s good value when you consider what this vehicle provides. The X5 can be everything from a luxury car to a family wagon, a cargo hauler, and even a reasonably capable off-roader (provided you don’t mind getting it dirty!). Under the bonnet is BMW’s acclaimed 3.0 litre DOHC straight six cylinder engine that also powers the 530i, 330i and Z3 models. It gives quite a spirited performance, considering the X5 weighs in at 2030 kg, and even sounds great under acceleration. Technology abounds in the X5, with all manner of controls designed to provide high levels of dynamic safety. These include Dynamic Stability Control (DSC III), Automatic Stability Control (ASC-X), Automatic Differential Brake (ADB-X), Hill Descent Control (HDC), Cornering Brake Control (CBC), Dynamic Brake Control (DBC) and Anti-lock Brakes (ABS).

The only suspension control system that the 3.0 litre model doesn’t get is self-levelling suspension with rear air suspension. Passive safety features in the X5 include 10 airbags, head restraints and lap/sash seat belts for all five occupants, and crash sensors included in the central locking system. Luxury equipment in the 3.0 litre X5 includes automatic climate control air conditioning, leather upholstery, CD player, power operated windows, exterior mirrors and tailgate, cruise control, tilt and telescopic steering wheel, and roof rails. Compared with the 4.4 litre X5, the 3.0 litre version misses out on electric front seats, the onboard monitor with TV and trip computer, a rear mounted CD stacker, park distance control, aluminium running boards and anti-dazzle interior and exterior mirrors. All of these items, plus satellite navigation, are available as options. High standards of finish are expected in a BMW costing $80,000-plus and the X5 doesn’t disappoint. Inside and out, it looks to be very well built, and the attention to detail is excellent. As for the V8 model, the 3.0 litre X5 offers good space in all five seating positions and there’s no rear floor hump to hinder a centre rear passenger’s comfort. The seats are firm, but generally comfortable, though there’s not a lot of lateral support when cornering. The luggage area is a good size for normal family requirements and the seat backrest folds in a 60/40 split when more load length is needed. The two-piece tailgate provides easy loading, though you have to stretch across the lower section to reach forward-placed items. The bottom tailgate section lowers to a horizontal position and could handily double as a bench or a seat at picnics.